CutListIQ — Cut List Report
⬛
No cuts optimized yet
Add stock sheets and parts, then click ▶ Optimize
Daily limit reached. Free accounts get 5 optimizations a day. Upgrade for unlimited.
Nothing optimized yetAdd your stock sheets and parts, then tap ▶ Optimize. |
Cabinet Builder PRO
Configure a cabinet, generate the full cut list, then optimize. Add multiple cabinets to build a complete job.
Cabinet Type
Dimensions
Construction Style
⬜
Frameless
European / full access
🪟
Face Frame
Traditional / NA style
Options
Construction Details
Doors
Toe Kick
Drawer Boxes
Face Frame Details
Materials (name must match a stock sheet; leave blank for the same as the box)
Edge Banding
Banding goes on the exposed edges automatically and turns on the Edge Banding tab with tape totals. Hidden edges (backs, toe kicks, stretchers, drawer boxes) stay bare.
Parts that will be generated
Hardware list (priced under Hardware & Extras)
▶ Construction Assumptions
Frameless Base / Drawer
Side Panels = Depth × Height (×2)
Bottom = (W − 2T) × Depth
Top Nailers = (W − 2T) × Nailer Height, quantity per setting
Back Panel = W × (H − T) when "Back sits on bottom" is on, else W × H. Thickness set independently (default ¼").
Adj. Shelf = (W − 2T − Side Clear) × (Depth − Setback)
Toe Kick = (W − 2T) × Toe Kick Height
Face Frame
Stiles = Stile Width × Full Height (×2)
Rails sized to opening width between stiles
Mid Stile added when 2-door is selected
Doors & Drawers
Door sizes include overlay; gap = 1/8" total (1/16" per side)
Drawer heights: equal by default; classic ratios when unchecked
All dimensions are finished sizes — kerf is applied during optimization only
Closet Builder PRO
Lay out a closet run section by section. Get the full cut list and hardware list, then optimize. Add more runs to build a complete job.
Closet Run
Sections (left to right — width is the inside opening)
| # | Type | Width (in) | Height (in) | Shelves | Drawers |
|---|
Front elevation
Base, Top & Back
Shelves & Drawers
Edge Banding
Banding goes on the exposed edges automatically and turns on the Edge Banding tab with tape totals. Hidden edges (backs, toe kicks, stretchers, drawer boxes) stay bare.
Parts that will be generated
Hardware list (not added to the cut list)
▶ Construction Assumptions
Uprights = Depth × tallest adjoining section height. Ends and dividers are each one panel (sections share dividers).
Top / Bottom / Fixed shelves = section width × Depth. Toe kick = section width × kick height, bottom panel sits on it.
Adj. / Shoe shelf = (width − side clear) × (Depth − setback). 4 shelf pins per adjustable shelf.
Drawer front = (width − 1/8") × front height. Box sides = nearest standard slide length ≤ Depth − 1". Box width = width − slide clearance. Box height = front height − 1". Box front/back fit between the sides; bottom sits in a 1/4" dado.
Drawers sit on the base; a fixed shelf closes the top of each drawer stack. Single hang: rod at 66" (centerline). Double hang: rods near 80" and 40".
Rods are cut 1/16" short of the section width. Sections over 36" wide get a sag warning; over 48" add a center rod support.
All dimensions are finished sizes — kerf is applied during optimization only. Edge banding is not preassigned.
Cabinet Layout PRO
Line up your cabinets along a wall, set the gaps, and see whether everything fits. Closets already have their own section layout inside the Closet Builder, though you can still place a whole closet on a wall here. Each wall also goes into your customer proposal.
Lumber & Trim Calculator PRO
Calculate board footage for solid wood (face frames, hardwood parts) and linear footage for trim and molding.
Board Footage — Solid Wood
BF = (thickness × width × length) ÷ 144
| Part / Species | Thick (in) | Width (in) | Length (in) | Qty | BF / pc | Total BF |
|---|
Board Footage Summary
Linear Footage — Trim & Molding
| Description (crown, base, casing…) | Length (in) | Qty | Lin. Ft |
|---|
Trim Summary